08 version available!!!
Now we have a possibility to put in the
newcamd server details, too!
It is possible to sort it all out via remote:
Home -> Plug-ins -> OpenXCAS -> Camd Setup -> MultiCAS -> Smartcard Interface -> SC Splitter and CS -> roll the options to Client CCcam or Client NewCamd and add as required...
The relevant config files to discuss:
cardreader.cfg
###### Disable or Enable option for cardreader of MultiCAS
###### Disable_CardReader = 1 -> Disable-Internel CardReader / Disable_CardReader = 0 -> Enable-Internel CardReader
Disable_CardReader = 0
Sorry, I do not yet have a smartcard, so can't help too much...
newcamd.cfg
## MAX Support the 12 of Serverlist by this CFG file
## N: Hostname port username password 01 02 03 04 05 06 07 08 09 10 11 12 13 14
priocaid.cfg
### 0100 : SECA
### 0500 : VIACESS
### 06xx : IRDETO
### 0dxx : CRYPTOWORKS
### 0bxx : CONAX
### 09xx : NDS
### 17xx : BETACRYPT
### 18xx : NAGRA
###----------------------------------------------------
### max 8 of caid 0100 0500 0600 0900 1800 0d00 0b00 1700
###----------------------------------------------------
### CASE OLD #1 0600 0d00 1700 1800 0900 0b00 0100 0500
### CASE OLD #2 0100 1800 0500 0600 0d00 1700 0b00 0900
###---------------------------------------------------
0100 1800 0500 0600 0d00 1700 0b00 0900
===============================================
One way of editing it all is using telesat's MultiCAS Edit.
================================================
Here is
the "how to" for 2 more options, from how to install it to how to edit it - easily:
0) Home -> Plug-ins -> OpenXCAS -> no more Manual Install option, guys! It is now
DOWNLOAD EXECUTABLE -> you will see the links of support servers to get your plug-ins there, guys... [ get it from
[url]http://azboxworld.com[/URL] ]
1) Download and install:
MultiCAS 160... well, the latest - always!
2) Get the
configuration files for camd/CS SW from DOWNLOAD CONFIG. So, one must
download MultiCAS CCcam config files. But not needed for this one, if you had the previous version of MultiCAS already installed and it was all functioning.
At this point it is good to reboot your AZbox HD!
3) So, off we go to
Home -> Plug-ins -> [as described above...] ->
MultiCAS ->
using your remote control -> Smart Card Splitter and CS.
4) Change the following, using your REMOTE:
-change the
Mode to
Client CCcam [if, like me, you have no smartcard to play with and share] - you can connect to other people's servers
-choose
Server No.
1 [when done with the first one, move this one to 2, then 3 etc. - as many as you need, up to 16, I think...]
-choose
Host Name Use - write something like:
something.dyndns.org [whatever the data you get from your server/peer is, like gorski.dyndns.org or whatever your server is called like - I DO NOT HAVE A SERVER, THIS IS ONLY AN EXAMPLE!!!],
-choose the
Port - 12000 or
whatever it is that your peer tells you to use
-User Name - whatever it is [you must have a username that normally your peer gives you and put in his server to allow you access to his server]
-Password - whatever it is [like above]
-Server -
Enable
-Connect - test it [but only AFTER I enabled the one which appears below it, on the TV screen...]
It should say "
login success"...
Repeat for all the servers you have, to check...
Red Button = Save.
5) But still: as soon as I wanted to get out of there using the
Exit button on my remote,
it first asked me, in a little pop-up window, if I want to login to all my servers now. Press
OK, of course. It will connect to your Leete las normas aaaaaand....
...once in a TV channels list, the connection was fast!!! Let's just leave it at that. Pink/Total TV [Irdeto/N*D*S]: vroom, vrooooommmm!!! :grin: If not, change the channel and then it should connect! If not - reboot and check again...
===============================================
Here is how to install it from a file you get on a forum like this one:
FileZilla -> into AZbox HD -> Plugins -> OpenXCAS -> MultiCAS ->
delete all "example" files, openxcas.conf and multicas emu_module.
Put in openxcas and emu_module files from a file one gets from a forum like this one.
Give emu_module CHMOD to 755.
Reboot.
The right version should be showing in AZbox HD MultiCAS menu. All servers should be preserved, if you put them in before!
Server details are in MultiCAS in /tmp file: ccc_serverstatus.info
Good luck!:have a nice day:
=======================================================================
Btw, I suppose that if we disable the MultiCAS card reader [using the cardreader.cfg file], we can activate NewCS alongside MultiCAS and use the 2 together.
So, if we activate NewCS 1.20 RC13 to use the internal card reader and we are servers to our Leete las normas, using Newcamd protocol, then we can have a full Newcamd package in NewCS + MultiCAS' Client NewCamd mode?
<newcamdserver>
<enabled>yes</enabled>
<name>local</name>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<user>
<name>dummy</name>
<password>dummy</password>
<au>on</au>
<sidoverride>off</sidoverride>
<hostname>127.0.0.1</hostname>
<port>22000</port>
</user>
</newcamd_server>
<httpd>
<server>
<port>8080</port>
<enabled>yes</enabled>
</server>
<user>
<name>azhd</name>
<password>azhd</password>
<accesslevel>admin</accesslevel>
</user>
</httpd>
</newCSconfig>
Would it be good enough for whatever it is we need...???
