ostia que raro borro el openxcas desde el mando reincio del boton trasero y cuando enciendo todavia esta hay el openxcas
0.9.4461
- Iniciador del tema gaizka71
- Fecha de inicio
pues CHapuceros de mierda si no esta bien la nueva openxcas no desactiveis la otra merluzos.
que malo son esta gente macho luego no quieren que les critiquen joder..
que malo son esta gente macho luego no quieren que les critiquen joder..
No hacen mas que cagarla release tras release... No funciona openxcas, el deco con este firmware está más inestable que nunca. He formateado todo y borrado, puesto de 0 y la lista de canales la cargo. Luego no entiendo porque con el de antes si me funcionaba y ahora con este no encuentra señal en los canales... ninguno. He hecho una busqueda de canales y fatal. No hay nada que hacer, cada vez que avanzamos damos un paso hacia delante y como 20 hacia atras.
tudo ok ahora!!!!
criei un ficheiro
"module.seq" em folder OpenXCAS
con isso:
MultiCAS
#mgcamd
reboot, ahora con >> aparece la lista de camd e es possivel configurar MultiCAS em menu PLUGINS
zapping vai fantastico ahora!!!!
criei un ficheiro
"module.seq" em folder OpenXCAS
con isso:
MultiCAS
#mgcamd
reboot, ahora con >> aparece la lista de camd e es possivel configurar MultiCAS em menu PLUGINS
zapping vai fantastico ahora!!!!
La busqueda de tiempo fijo en peliculas tambien se ha estropeado. Se queda como 4 firmwares antes y ya estaba resuelto.
- 10 Abr 2009
- 1.334
- 9
- 0
It will work, using your old MultiCAS from the previous FW + telesat's MultiCASedit! Beware, not all is OK with the new OpenXCAS and therefore MultiCAS!
============PROCEDURE===========
0) I put patch.bin on my USB memory stick and inserted it into AZbox HD.
Used my remote:
1) Home -> Setings -> Backup -> [to your USB stick] Channel list. No point in saving the Plugins like this, since we have to re-install OpenXCAS from scratch. Back them up via FileZilla Client, though! Make sure you have the new MultiCAS installed, then back it up!
2) [optional - if not, go to step 4!] Home -> Settings -> Data Reset -> PIN [0000] -> Delete all channels, then Delete plugins, then Factory Reset -> machine reboots.
3) [optional] Upgrade Menu: Format application area -> OK -> when done press Exit key.
4) Upgrade Menu -> USB -> press OK to upgrade with FW 4461.
When done AZbox HD reboots.
5) [optional] Settings Menu -> Data Reset -> Factory Setting -> OK, to do the reset -> confirm. AZ HD should now reboot, again. It should now be as clean as possible, from the old stuff in it...
6) [optional but necessary, if done steps 2, 3 & 5] Setup -> System Information -> Backup/Restore -> Channel -> choose where you put it beforehand, when you backed it up -> OK -> it will tell you if it was successful... You have your old settings list back in your AZbox HD. But I had to redo my DiSEqC 1.1 settings, as not everything was restored.
To back-up and restore your channel/settings list, you can also use Morser's MaZ program, telesat's channel editor or SetEdit for AZ HD. These programs should preserve all your settings properly, including the DiSEqC ones!
7) [optional but necessary, if done steps 2, 3 & 5] Now, sort out all the settings according to your needs [I go for Language, HDMI, 1080p, DHCP, Network (DynDNS etc.) etc. etc.].
When done check out the picture quality etc.
Now, download/install OpenXCAS first and then MultiCAS. After that restore the rest of your Plugins. So...8) Home -> Plugins -> red button on your remote -> azboxworld link -> OK -> OpenXCAS. When it is done - reboot!
9) Home -> Plugins -> OpenXCAS -> Download Executable -> MultiCAS version 1.62B.After that go to Download Config for MultiCAS.
But! Since there is a problem going into the MultiCAS menu to activate and edit it - I had to restore some of the files using FileZilla [I did: module, splitterdata txt and bin, plus Data9F files], as described in my "Alternative Guide..."
Make sure the module and other relevant files are given the 755 ["CHMOD"] Attributes, as described in my "guide"!!!
Then, I started telesat's MultiCASedit and I messed with it to make it work: in "Splitter & CCcam" tab I clicked on "Receive from AZbox HD", then I clicked on "Sent to AZbox", to activate it.
I also restored the rest of my camd/CS SW/plugins and other files in Plugins and OpenXCAS. Again, all the modules and other relevant files must be given the 755 ["CHMOD"] Attributes.
Make sure you have module.seq file in OpenXCAS folder. Mine looks like this:
All was working, all my camd/CS SW/Plugins. :desmayo::XD:
Once again: some buttons/functions in some menus, for some camd - are not working 100% properly [read "as before"], as you will see: EXIT button etc.
============PROCEDURE===========
0) I put patch.bin on my USB memory stick and inserted it into AZbox HD.
Used my remote:
1) Home -> Setings -> Backup -> [to your USB stick] Channel list. No point in saving the Plugins like this, since we have to re-install OpenXCAS from scratch. Back them up via FileZilla Client, though! Make sure you have the new MultiCAS installed, then back it up!
2) [optional - if not, go to step 4!] Home -> Settings -> Data Reset -> PIN [0000] -> Delete all channels, then Delete plugins, then Factory Reset -> machine reboots.
3) [optional] Upgrade Menu: Format application area -> OK -> when done press Exit key.
4) Upgrade Menu -> USB -> press OK to upgrade with FW 4461.
When done AZbox HD reboots.
5) [optional] Settings Menu -> Data Reset -> Factory Setting -> OK, to do the reset -> confirm. AZ HD should now reboot, again. It should now be as clean as possible, from the old stuff in it...
6) [optional but necessary, if done steps 2, 3 & 5] Setup -> System Information -> Backup/Restore -> Channel -> choose where you put it beforehand, when you backed it up -> OK -> it will tell you if it was successful... You have your old settings list back in your AZbox HD. But I had to redo my DiSEqC 1.1 settings, as not everything was restored.
To back-up and restore your channel/settings list, you can also use Morser's MaZ program, telesat's channel editor or SetEdit for AZ HD. These programs should preserve all your settings properly, including the DiSEqC ones!
7) [optional but necessary, if done steps 2, 3 & 5] Now, sort out all the settings according to your needs [I go for Language, HDMI, 1080p, DHCP, Network (DynDNS etc.) etc. etc.].
When done check out the picture quality etc.
Now, download/install OpenXCAS first and then MultiCAS. After that restore the rest of your Plugins. So...8) Home -> Plugins -> red button on your remote -> azboxworld link -> OK -> OpenXCAS. When it is done - reboot!
9) Home -> Plugins -> OpenXCAS -> Download Executable -> MultiCAS version 1.62B.After that go to Download Config for MultiCAS.
But! Since there is a problem going into the MultiCAS menu to activate and edit it - I had to restore some of the files using FileZilla [I did: module, splitterdata txt and bin, plus Data9F files], as described in my "Alternative Guide..."
Make sure the module and other relevant files are given the 755 ["CHMOD"] Attributes, as described in my "guide"!!!
Then, I started telesat's MultiCASedit and I messed with it to make it work: in "Splitter & CCcam" tab I clicked on "Receive from AZbox HD", then I clicked on "Sent to AZbox", to activate it.
I also restored the rest of my camd/CS SW/plugins and other files in Plugins and OpenXCAS. Again, all the modules and other relevant files must be given the 755 ["CHMOD"] Attributes.
Make sure you have module.seq file in OpenXCAS folder. Mine looks like this:
When I was done I rebooted!
All was working, all my camd/CS SW/Plugins. :desmayo::XD:
Once again: some buttons/functions in some menus, for some camd - are not working 100% properly [read "as before"], as you will see: EXIT button etc.
- 14 Abr 2009
- 179
- 5
- 0
gorski dijo:
Now the exit button (backward) in OpenXCAS is the menu button. If you pulse the exit button, you will finish the OpenXCAS.
Ahora el boton (ir hacia atras) en el OpenXCAS es el boton donde sacas los menus laterales. Si pulsas el boton exit, lo que hace es salirse del OpenXCAS
Yo no he tenido que hacer lo del module.seq que dice gorski. Sino una vez instalas el nuevo OpenXCAS, y despues el multicas, lo que hice fue entrar en el menu donde activas y desactivas las camd. Cuando entras no ves que haya ninguna camd instalada, pero le empiezas a dar al boton azul (como si fueras a desactivar la camd), y zas... ya sale #MultiCAS. Tras esto le volveis a dar al boton azul y luego al amarillo para rearrancar la camd, y todo listo
:okb:
hfmls dijo:
macho es una cagada digs lo que tu quieras decir a mi no me vendas el casco si no tengo moto
!??!!?
yo estava tentando ajudar!
se no quieres ajuda es teu problema!!
MAL AGRADECIDO!
aqui ahora esta tudo a 100%
é so lir lo que esta escrito!!
yo estava tentando ajudar!
se no quieres ajuda es teu problema!!
MAL AGRADECIDO!
aqui ahora esta tudo a 100%
é so lir lo que esta escrito!!
a mi me pasaba como a frankcis, al ir a cargar la multicas se me quedaba en DATA LOADING.
# fuàa multicas desde el deco y quité la almohadilla ( activar con el botón azul). luego OK
saludos y a ver si con un poco de suerte vamos avanzando
# fuàa multicas desde el deco y quité la almohadilla ( activar con el botón azul). luego OK
saludos y a ver si con un poco de suerte vamos avanzando
hfmls dijo:
creo que entendistes mal no te hecho a ti la culpa por dios como vas a tenerla tu..
otra cosa ahora no me deja descargarme el multicas los link que estan dentro de openxcas an desaparecido..
saludos
ya he conseguido que me reconozca el multicas pero cuando intento reinicar el multicas desde el boton >>| se queda colgado y tengo que reinciar
frankcis dijo:
cuando le das a download executable y te aparece el server, edita uno de los que hay, cambiandolo por azboxworld.com. creo que para editar hay que darle al botón azul del mando ( de todas formas, lo pone cuando estás ahÃÂÂ)