amigos necesito de su ayuda he intentado de todo y nada me funciona, al recuperar con yamon llego hasta la ultima parte cd/tmp pero me sale
-sh cd/tmp: no surch file or directory , que puedo hacer? alguien le a pasado esto?
Pues mal lo tienes, no hace el control+c, este error lo encontraras en este mismo hilo si no me equivoco.AZBOX[tmp]$ chmod a+x update
AZBOX[tmp]$ ./update /MMP/backup_kernel
INFILE: /MMP/backup_kernel, OUTFILE:/dev/mtdblock4
HX_DD: 0+0 records in
HX_DD: 0+0 records out
Updating old kernel finished!
Rebooting...
The system is going down NOW!
Sent SIGTERM to all processes
Terminated
Sent SIGKILL toRestarting system.
xosPe0 serial#ce8b8cd738257fcb1548e7e515038012 subid 0x50
xenv cs2 ok
power supply: ok
dram0 ok (9)
dram1 ok (a)
zboot (0) ok
>
**************************************
* SMP863x zboot start ...
* Version: 2.4.0-2.8.0.1
* Started at 0x91000000.
* Configurations (chip revision: 6):
* Use 8KB DRAM as stack.
* Support XLoad format.
* Enabled BIST mode.
* Enabled memory test mode.
* Use internal memory for stage0/1.
**************************************
Boot from flash (0x48000000) mapped to 0x8c000000.
Found XENV block at 0x8c000000.
CPU clock frequency: 300.37MHz.
System clock frequency: 200.25MHz.
DRAM0 dunit_cfg/delay0_ctrl (0xf34111ba/0x000a8888).
DRAM1 dunit_cfg/delay0_ctrl (0xf34111ba/0x00098887).
Using UART port 0 as console.
Board ID.: "852-E2"
Chip Revision: 0x8634:0x86 .. Matched.
Setting up H/W from XENV block at 0x8c000000.
Setting <SYSCLK avclk_mux> to 0x00000000.
Setting <SYSCLK hostclk_mux> to 0x00000100.
Setting <IRQ rise edge trigger lo> to 0xff28ca00.
Setting <IRQ fall edge trigger lo> to 0x0000c000.
Setting <IRQ rise edge trigger hi> to 0x0000009f.
Setting <IRQ fall edge trigger hi> to 0x00000000.
Setting <IRQ GPIO map> to 0x20090820.
Setting <PB default timing> to 0x10101010.
Setting <PB timing0> to 0x10101010.
Setting <PB Use timing0> to 0x000003f4.
Setting <PB timing1> to 0x00110101.
Setting <PB Use timing1> to 0x000003f3.
Setting <PB timing2> to 0x105f1010.
Setting <PB Use timing2> to 0x000003f8.
PB cs config: 0x000e0040 (use 0x000e0040)
Enabled Devices: 0x00021ace
BM/IDE PCIHost Ethernet I2CM I2CS USB PCIDev2 PCIDev3 SCARD
MAC: 00:02:14:14:44:a3
PCI IRQ routing:
IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
IDSEL 3: INTA(#15) INTB(#15) INTC(#15) INTD(#15)
Smartcard pin assignments:
OFF pin = 0
5V pin = 1
CMD pin = 2
Setting up Clean Divider 2 to 96000000Hz.
Setting up Clean Divider 4 to 33333333Hz.
Setting up Clean Divider 5 to 25000000Hz.
Setting up Clean Divider 6 to 20000000Hz.
Setting up Clean Divider 7 to 20000000Hz.
GPIO dir/data = 0x76000038/0x76000000
UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
UART1 GPIO mode/dir/data = 0x6e/0x00/0x00
XENV block processing completed.
Found existing memcfg: DRAM0(0x08000000), DRAM1(0x08000000)
Heap/Temp/Temp1/Dest start at 0x14000000/0x16000000/0x15000000/0x12000000.
Default boot index: 0
Scanning ROMFS image at 0x8c040000 (0x48040000) .. Found.
ROMFS found at 0x8c040000, Volume name = YAMON_XRPC
Found 1 file(s) to be processed in ROMFS.
Processing xrpc_xload_yamon_ES4_prod.bin (start: 0x8c040090, size: 0x0002fe84)
Checking zboot file signature .. Not found.
Trying xrpc_xload format .. OK
Checking zboot file signature at 0x13000000 .. OK
Decompressing to 0x91200000 .. OK (453328/0x6ead0).
Load time total 173/255 msec.
Execute final at 0x91200000 ..
**********************************
* YAMON ROM Monitor
* Revision 02.06-SIGMADESIGNS-01-2.8.0.1
**********************************
Memory: code: 0x11000000-0x11040000, 0x11200000-0x11204000
reserved data: 0x11240000-0x12440000, PCI memory: 0x12440000-0x12840000
Environment variable 'start' exists. After 1 seconds
it will be interpreted as a YAMON command and executed.
Press Ctrl-C (or do BREAK) to bypass this.
ROMFS not found from 0xac080000 to 0xac080100
Checking zboot signature.. it's not zboot file.
Error : Internal, code = ffffffff
ahora este es mi problema
asi es ASU lleva los mismo componetes en reguladores de voltajes y demas que el ELITE. yo tube un elite y tengo un premiu hd, en sus tiempo ke tube los 2 verifike los reguladore y son exactamente los mismos. solo cambia el voltaje sl2Leí después que se trata de un Premium HD, esta placa no la conozco tanto como la del Elite pero me imagino que llevara el mismo o los mismos reguladores y derivados que son los que suelen fallar.
Por otro lado mientras el putty no te lo reconozca sera imposible recuperarlo via Jtag, al igual que el putty, el puerto Jtag estará esperando a que enciendas el azbox aunque lo tengas encendido.
Es avería en placa, intenta de reiniciar de 4 a 5 veces con el boton trasero dejando un intervalo de 30 segundos en cada reinicio, si haces esos 5 o 6 reinicio y no arranca, difícil esta para poderlo solucionar.
buenas noches españa, buenas tardes america, amigo mi pregunta es ya revisaste tu placa bien a bien?? no se ve alguncomponente quemado o botado dela soldadura? eso puede ser x ke no te detecta el cable usb, o el jtag. pero recuerda necesitas una lupa minimo para poder detectar . ah y hay reguladores de voltaje de 3v. ke llevan tanto los modelo elite como premium , hay que revisar esos con cuidado ya que a simple vista se ven bien pero se dañan internamente. hay un post aqui mismo en los modelo Me, que yo puse y habla refernte a ese chip revisalo bien.sl2Buenas noches lilo74,¿ me podrias deci qie reguladores o que componente suelen fallar para ver si los puedo cambiar o comprar en algun sitio?
Gracias