Problema instalacion tdt xbox en qviart lunix3 4k

[esehomo]

Buenas tardes,

He conectado por usb el tdt xbox en un qviart lunix3 4k, que a su vez tiene instalado un tuner de tdt interno. He probado tanto instalación automática (
spa-dvb-module-dib0070
spa-dvb-module-dib0090
spa-dvb-module-dib3000
spa-dvb-module-dib7000)
como manual, pero se queda en estado amarillo. He reiniciado tras la instalación el deco, lo he apagado de corriente y he reiniciado gui, sin éxito en ninguna de ellas. He pulsado también sobre cargar, una vez instalado, pero no parece que haga nada. ¿Es posible que este deco no permita dos tuner de tdt?

 

[esehomo]

En los logs de enigma he encontrado esto...
<6>[ 1431.652518] dvb-usb: found a 'Microsoft Xbox One Digital TV Tuner' in cold state, will try to load a firmware
<6>[ 1431.665706] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.20.fw'
<6>[ 1431.880480] dib0700: firmware started successfully.
<6>[ 1432.385517] dvb-usb: found a 'Microsoft Xbox One Digital TV Tuner' in warm state.
<6>[ 1432.395507] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
<6>[ 1432.411260] dvb-usb: Microsoft Xbox One Digital TV Tuner error while loading driver (-23)

 

[Tururu]

En general los receptores soportan tuner TDT interno y tambien usb-tdt sin problemas.
Como en ese deco nunca instale USB-TDT, solo TDT interno como tienes, mientras esperas a los que saben.....

Para ver que soporta usb-tdt (vtuner), repasa el post 12 de este hilo.

TDT-USB - USB-TDT (DVB-T) normales soportados, al final tienes TDT2 y cable (DVB-T2/DVB-C) y como ver si soporta USB-TDT

Voy a ir poniendo una lista de los pinchos tdt que mas usamos. Desde la version OpenSPA7.2.006 se instalan "solos/automaticamente" los driver usb-tdt (al final una instalacion en automatico). Mejor contado en 2018 (Automatico y Manual).... OpenSPA 7.2.006. Guia rapida funcionamiento drivers...

openspa.info

PD: No olvides los datos que faltan, gracias...Qviart lunix3 4k con imagen x.x.xxx?
.

 

[esehomo]

Buenas,

Pongo todos los datos del software por si acaso. Gracias.

Decodificador
Marca & Modelo:	qviart LUNIX3 4K
Chipset:	7252S

Sistema OE:	OE-Alliance 5.0
Versión firmware:	openspa 8.0.001 (2022-05-21)
Versión Kernel / Fecha de driver:	3.14.28 / 20210427

Y me aparecen estos sintonizadores, porque instalé un adicional en un hueco opcional que tenía el deco:

Sintonizadores
Sint. A	DVB-S NIM(45208 FBC) (DVB-S2)
Sint. B	DVB-S NIM(45208 FBC) (DVB-S2)
Sint. C	DVB-S NIM(45208 FBC) (DVB-S2)
Sint. D	DVB-S NIM(45208 FBC) (DVB-S2)
Sint. E	DVB-S NIM(45208 FBC) (DVB-S2)
Sint. F	DVB-S NIM(45208 FBC) (DVB-S2)
Sint. G	DVB-S NIM(45208 FBC) (DVB-S2)
Sint. H	DVB-S NIM(45208 FBC) (DVB-S2)
Sint. I	AVL FTT9760 (external) (DVB-T2)

Del POST que adjuntas, sólo veo esto, en el que solo me aparece un vtuner. No sé si es el que detecta o que mi sistema solo permite tener 1. La verdad que no lo he terminado de entender.

root@lunix34k:~# cd /dev/misc/
root@lunix34k:/dev/misc# ls
rtc vtuner0
root@lunix34k:/dev/misc# ls -l
crw-rw-rw- 1 root root 10, 54 Sep 10 20:30 rtc
crw-rw---- 1 root root 266, 0 Sep 10 20:31 vtuner0

 

[Tururu]

En teoria soporta 1 tuner USB-TDT.
Ante la duda, quita el tuner TDT interno y sales de dudas en un pis pas.

En los equipos que tengo, siempre pude hacer pruebas con tantos tuner usb-tdt como indica que tiene.
Aparte de los internos/originales.
Por preguntar, el Xbox usb-tdt lo probaste en otro equipo? y funciona ok?.
Tienes otro usb-tdt de los soportados para hacer pruebas?

En este punto tocara esperar a los que saben, algo no le gusta al deco y no termina de cargar bien el driver.
.

 

[evox]

Buenas,

Pongo todos los datos del software por si acaso. Gracias.

Decodificador
Marca & Modelo:	qviart LUNIX3 4K
Chipset:	7252S

Sistema OE:	OE-Alliance 5.0
Versión firmware:	openspa 8.0.001 (2022-05-21)
Versión Kernel / Fecha de driver:	3.14.28 / 20210427

Y me aparecen estos sintonizadores, porque instalé un adicional en un hueco opcional que tenía el deco:

Sintonizadores
Sint. A	DVB-S NIM(45208 FBC) (DVB-S2)
Sint. B	DVB-S NIM(45208 FBC) (DVB-S2)
Sint. C	DVB-S NIM(45208 FBC) (DVB-S2)
Sint. D	DVB-S NIM(45208 FBC) (DVB-S2)
Sint. E	DVB-S NIM(45208 FBC) (DVB-S2)
Sint. F	DVB-S NIM(45208 FBC) (DVB-S2)
Sint. G	DVB-S NIM(45208 FBC) (DVB-S2)
Sint. H	DVB-S NIM(45208 FBC) (DVB-S2)
Sint. I	AVL FTT9760 (external) (DVB-T2)

Del POST que adjuntas, sólo veo esto, en el que solo me aparece un vtuner. No sé si es el que detecta o que mi sistema solo permite tener 1. La verdad que no lo he terminado de entender.

root@lunix34k:~# cd /dev/misc/
root@lunix34k:/dev/misc# ls
rtc vtuner0
root@lunix34k:/dev/misc# ls -l
crw-rw-rw- 1 root root 10, 54 Sep 10 20:30 rtc
crw-rw---- 1 root root 266, 0 Sep 10 20:31 vtuner0

Versión firmware:

openspa 8.0.001 (2022-05-21)

Mejor actualizas la imagen que ya vamos por 8.4.001 y si en la nueva siguen los problemas hablamos.

Salu2.

 

[esehomo]

Buenos días,

He actualizado a 8.4 con mismo resultado. He pasado a off la autoinstalación y conectado el USB. Posteriormente por terminal he hecho esto:

root@lunix34k:~# opkg update
Downloading https://openspa.webhop.info/feeds/8.4/dags7252/all/Packages.gz.
Updated source 'openspa-all'.
Downloading https://openspa.webhop.info/feeds/8.4/dags7252/cortexa15hf-neon-vfpv4/Packages.gz.
Updated source 'openspa-cortexa15hf-neon-vfpv4'.
Downloading https://openspa.webhop.info/feeds/8.4/dags7252/dags7252/Packages.gz.
Updated source 'openspa-dags7252'.
Downloading https://raw.githubusercontent.com/oe-alliance/enigma2-settings-feed/gh-pages/Packages.gz.
Updated source 'enigma2-settings-feed'.
Downloading https://openspa.webhop.info/feeds/8.4/dags7252/lunix34k/Packages.gz.
Updated source 'openspa-lunix34k'.
Downloading https://openspa.webhop.info/feeds/8.4/dags7252/static-cortexa15hf-neon-vfpv4/Packages.gz.
* opkg_download_backend: Failed to download https://openspa.webhop.info/feeds/8.4/dags7252/static-cortexa15hf-neon-vfpv4/Packages.gz, wget returned 8.
Downloading https://openspa.webhop.info/feeds/8.4/dags7252/static-dags7252/Packages.gz.
* opkg_download_backend: Failed to download https://openspa.webhop.info/feeds/8.4/dags7252/static-dags7252/Packages.gz, wget returned 8.
root@lunix34k:~# opkg install enigma2-plugin-drivers-dvb-usb-dib0700
enigma2-plugin-drivers-dvb-usb-dib0700: unsatisfied recommendation for kernel-module-mn88472
enigma2-plugin-drivers-dvb-usb-dib0700: unsatisfied recommendation for kernel-module-tda18250
enigma2-plugin-drivers-dvb-usb-dib0700: unsatisfied recommendation for kernel-module-tuner-xc2028
Installing firmware-dvb-usb-dib0700-1.20 (1.0) on root.
Downloading https://openspa.webhop.info/feeds/8.4/dags7252/all/firmware-dvb-usb-dib0700-1.20_1.0-r0_all.ipk.
Installing firmware-dvb-usb-dibusb-5.0.0.11 (1.0) on root.
Downloading https://openspa.webhop.info/feeds/8.4/dags7252/all/firmware-dvb-usb-dibusb-5.0.0.11_1.0-r0_all.ipk.
Installing firmware-dvb-usb-dibusb-6.0.0.8 (1.0) on root.
Downloading https://openspa.webhop.info/feeds/8.4/dags7252/all/firmware-dvb-usb-dibusb-6.0.0.8_1.0-r0_all.ipk.
Installing firmware-dvb-usb-dibusb-an2235-01 (1.0) on root.
Downloading https://openspa.webhop.info/feeds/8.4/dags7252/all/firmware-dvb-usb-dibusb-an2235-01_1.0-r0_all.ipk.
Installing firmware-mn8847x (1.0) on root.
Downloading https://openspa.webhop.info/feeds/8.4/dags7252/all/firmware-mn8847x_1.0-r0_all.ipk.
Installing firmware-xc3028-v27 (1.0) on root.
Downloading https://openspa.webhop.info/feeds/8.4/dags7252/all/firmware-xc3028-v27_1.0-r0_all.ipk.
Installing firmware-xc3028l-v36 (1.0) on root.
Downloading https://openspa.webhop.info/feeds/8.4/dags7252/all/firmware-xc3028l-v36_1.0-r0_all.ipk.
Installing kernel-module-dib0070-3.14.28 (3.14.28) on root.
Downloading https://openspa.webhop.info/feeds/8...odule-dib0070-3.14.28_3.14.28-11_dags7252.ipk.
Installing kernel-module-dib0090-3.14.28 (3.14.28) on root.
Downloading https://openspa.webhop.info/feeds/8...odule-dib0090-3.14.28_3.14.28-11_dags7252.ipk.
Installing kernel-module-dib3000mb-3.14.28 (3.14.28) on root.
Downloading https://openspa.webhop.info/feeds/8...ule-dib3000mb-3.14.28_3.14.28-11_dags7252.ipk.
Installing kernel-module-dibx000-common-3.14.28 (3.14.28) on root.
Downloading https://openspa.webhop.info/feeds/8...ibx000-common-3.14.28_3.14.28-11_dags7252.ipk.
Installing kernel-module-dib3000mc-3.14.28 (3.14.28) on root.
Downloading https://openspa.webhop.info/feeds/8...ule-dib3000mc-3.14.28_3.14.28-11_dags7252.ipk.
Installing kernel-module-dib7000m-3.14.28 (3.14.28) on root.
Downloading https://openspa.webhop.info/feeds/8...dule-dib7000m-3.14.28_3.14.28-11_dags7252.ipk.
Installing kernel-module-dib7000p-3.14.28 (3.14.28) on root.
Downloading https://openspa.webhop.info/feeds/8...dule-dib7000p-3.14.28_3.14.28-11_dags7252.ipk.
Installing kernel-module-dib8000-3.14.28 (3.14.28) on root.
Downloading https://openspa.webhop.info/feeds/8...odule-dib8000-3.14.28_3.14.28-11_dags7252.ipk.
Installing kernel-module-dvb-usb-3.14.28 (3.14.28) on root.
Downloading https://openspa.webhop.info/feeds/8...odule-dvb-usb-3.14.28_3.14.28-11_dags7252.ipk.
Installing kernel-module-dib9000-3.14.28 (3.14.28) on root.
Downloading https://openspa.webhop.info/feeds/8...odule-dib9000-3.14.28_3.14.28-11_dags7252.ipk.
Installing kernel-module-dvb-usb-dib0700-3.14.28 (3.14.28) on root.
Downloading https://openspa.webhop.info/feeds/8...b-usb-dib0700-3.14.28_3.14.28-11_dags7252.ipk.
Installing kernel-module-dvb-usb-dibusb-common-3.14.28 (3.14.28) on root.
Downloading https://openspa.webhop.info/feeds/8...dibusb-common-3.14.28_3.14.28-11_dags7252.ipk.
Installing kernel-module-dvb-usb-dibusb-mc-3.14.28 (3.14.28) on root.
Downloading https://openspa.webhop.info/feeds/8...usb-dibusb-mc-3.14.28_3.14.28-11_dags7252.ipk.
Installing kernel-module-fc0013-3.14.28 (3.14.28) on root.
Downloading https://openspa.webhop.info/feeds/8...module-fc0013-3.14.28_3.14.28-11_dags7252.ipk.
Installing kernel-module-mt2060-3.14.28 (3.14.28) on root.
Downloading https://openspa.webhop.info/feeds/8...module-mt2060-3.14.28_3.14.28-11_dags7252.ipk.
Installing kernel-module-mt2266-3.14.28 (3.14.28) on root.
Downloading https://openspa.webhop.info/feeds/8...module-mt2266-3.14.28_3.14.28-11_dags7252.ipk.
Installing enigma2-plugin-drivers-dvb-usb-dib0700 (1.0) on root.
Downloading https://openspa.webhop.info/feeds/8...plugin-drivers-dvb-usb-dib0700_1.0-r1_all.ipk.
Configuring firmware-xc3028l-v36.
Configuring kernel-module-dibx000-common-3.14.28.
Configuring kernel-module-dib9000-3.14.28.
Configuring kernel-module-dib3000mc-3.14.28.
Configuring kernel-module-fc0013-3.14.28.
Configuring kernel-module-dvb-usb-3.14.28.
Configuring firmware-mn8847x.
Configuring kernel-module-dib7000p-3.14.28.
Configuring firmware-dvb-usb-dibusb-an2235-01.
Configuring kernel-module-dvb-usb-dibusb-common-3.14.28.
Configuring kernel-module-dib0090-3.14.28.
Configuring kernel-module-dib0070-3.14.28.
Configuring kernel-module-dib7000m-3.14.28.
Configuring kernel-module-dib8000-3.14.28.
Configuring kernel-module-dvb-usb-dib0700-3.14.28.
Configuring firmware-dvb-usb-dib0700-1.20.
Configuring firmware-xc3028-v27.
Configuring kernel-module-mt2060-3.14.28.
Configuring kernel-module-mt2266-3.14.28.
Configuring kernel-module-dvb-usb-dibusb-mc-3.14.28.
Configuring firmware-dvb-usb-dibusb-6.0.0.8.
Configuring kernel-module-dib3000mb-3.14.28.
Configuring firmware-dvb-usb-dibusb-5.0.0.11.
Configuring enigma2-plugin-drivers-dvb-usb-dib0700.

He reiniciado y seguía en rojo. Le he dado con el botón del mando a instalar, y vuelto a reiniciar. Ahora en amarillo.
He pulsado en cargar y me ha salido un comando modprobe.... Después de reiniciar, continua en amarillo. He apagado y encendido con el botón de detrás y mismo resultado.

 

[evox]

Estas mezclando churras con meninas, deberias leerte bien el hilo de usbs-tdt de tururu. Para empezar el usb tdt xbox solo funciona con los drivers automaticos de openspa que son los que gestiona el plugin de dispositivos usb, los que tu instalas por telnet son los de oe-a que crean conflicto con los de openspa. Instalas imagen, una vez configurada apagas el deco completamente pinchas el tdt xbox y enciendes, cuando arranque te cas al gestor de dispositivos usb si sale amarillo haces un dmesg por telnes y nos lo pones, si sale rojo pulsas en instalar y segun pase haces, no instales nada por telnet por tu cuenta o la lias otra vez.

Salu2

 

[esehomo]

Ok, gracias. Me lo recomendaron en otro canal. Vuelvo otra vez a instalarlo y os comento. Lo del dmesg me suena haberlo visto en otros temas pero no lo he hecho nunca. Busco info ahora tb si falla. Gracias

 

[esehomo]

Buenas... mismo resultado. Os copio el dmesg. Es instalación limpia, sin copia de seguridad. He puesto la instalación automática en off, le he dado a instalar, y reiniciado cuando me ha pedido. Como estaba en amarillo, le he dado a cargar, y reiniciado gui. Como seguía en amarillo, he apagado deco y vuelto a encender, y sigue amarillo.

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.28 ([email protected]) (gcc version 13.2.0 (GCC) ) #1 SMP Fri Feb 24 05:23:03 UTC 2017
[ 0.000000] CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=30c7387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] Machine model: BCM97252SSAT_V00
[ 0.000000] moving dtb from 0x0000000007628000 to 0x0000000000943430
[ 0.000000] cma: Reserved 504 MiB at 0x0000000010000000
[ 0.000000] cma: Reserved 260 MiB at 0x000000002f800000
[ 0.000000] cma: Reserved 1020 MiB at 0x0000000080000000
[ 0.000000] cma: Reserved 16 MiB at 0x000000000f000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 524288
[ 0.000000] free_area_init_node: node 0, pgdat c0903e40, node_mem_map cd7f2000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65536 pages, LIFO batch:15
[ 0.000000] HighMem zone: 5632 pages used for memmap
[ 0.000000] HighMem zone: 458752 pages, LIFO batch:31
[ 0.000000] MCP: Enabling write pairing
[ 0.000000] PERCPU: Embedded 8 pages/cpu @cd7c0000 s9536 r8192 d15040 u32768
[ 0.000000] pcpu-alloc: s9536 r8192 d15040 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 523776
[ 0.000000] Kernel command line: root=/dev/mmcblk0p4 rootwait rw rootwait=data=journal debug,nolock coherent_pool=2M brcm_cma=504M@0x10000000 brcm_cma=260M@0x2f800000 br
cm_cma=1020M@0x80000000 hwtypenum=264
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 219400K/2097152K available (6648K kernel code, 348K rwdata, 1984K rodata, 265K init, 200K bss, 34552K reserved, 1843200K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0876524 (8634 kB)
[ 0.000000] .init : 0xc0877000 - 0xc08b9540 ( 266 kB)
[ 0.000000] .data : 0xc08ba000 - 0xc0911300 ( 349 kB)
[ 0.000000] .bss : 0xc0911308 - 0xc0943430 ( 201 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc403000, parent irq: 93)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc3e1000, parent irq: 64)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc410640, parent irq: 95)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc4d1200, parent irq: 58)
[ 0.000000] Architected cp15 timer(s) running at 27.00MHz (virt).
[ 0.000004] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 2545165795328ns
[ 0.000008] Switching to timer-based delay loop
[ 0.000199] Console: colour dummy device 80x30
[ 0.000217] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=27000)
[ 0.000225] pid_max: default: 32768 minimum: 301
[ 0.000311] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000316] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.005953] CPU: Testing write buffer coherency: ok
[ 0.006156] CPU0: update cpu_power 1024
[ 0.006163] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.006322] Setting up static identity map for 0x65a848 - 0x65a8a0
[ 0.008470] CPU1: Booted secondary processor
[ 0.008490] CPU1: update cpu_power 1024
[ 0.008493] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.008555] Brought up 2 CPUs
[ 0.008565] SMP: Total of 2 processors activated.
[ 0.008569] CPU: All CPU(s) started in SVC mode.
[ 0.008899] devtmpfs: initialized
[ 0.012063] VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0
[ 0.039256] regulator-dummy: no parameters
[ 0.039473] NET: Registered protocol family 16
[ 0.040679] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[ 0.041413] cpuidle: using governor ladder
[ 0.041419] cpuidle: using governor menu
[ 0.043773] irq: no irq domain found for /rdb/interrupt-controller@f040a700 !
[ 0.043908] irq: no irq domain found for /rdb/interrupt-controller@f0417380 !
[ 0.047085] irq: no irq domain found for /rdb/interrupt-controller@f03e1a00 !
[ 0.047319] syscon f0404000.syscon: regmap [mem 0xf0404000-0xf0404523] registered
[ 0.047456] syscon f0404100.syscon: regmap [mem 0xf0404100-0xf040415b] registered
[ 0.047608] syscon f040415c.syscon: regmap [mem 0xf040415c-0xf040419b] registered
[ 0.047747] syscon f0410700.syscon: regmap [mem 0xf0410700-0xf041070b] registered
[ 0.047872] syscon f041070c.syscon: regmap [mem 0xf041070c-0xf0410713] registered
[ 0.047991] syscon f1101004.syscon: regmap [mem 0xf1101004-0xf1101403] registered
[ 0.048110] syscon f1181004.syscon: regmap [mem 0xf1181004-0xf1181403] registered
[ 0.048246] syscon f0404080.syscon: regmap [mem 0xf0404080-0xf0404083] registered
[ 0.048380] syscon f04040a4.syscon: regmap [mem 0xf04040a4-0xf04040a7] registered
[ 0.048495] syscon f03e0154.syscon: regmap [mem 0xf03e0154-0xf03e0157] registered
[ 0.048611] syscon f03e0354.syscon: regmap [mem 0xf03e0354-0xf03e0357] registered
[ 0.048734] syscon f03e0400.syscon: regmap [mem 0xf03e0400-0xf03e0403] registered
[ 0.049263] irq: no irq domain found for /rdb/interrupt-controller@f0417380 !
[ 0.049735] syscon f03e2400.syscon: regmap [mem 0xf03e2400-0xf03e27ff] registered
[ 0.049886] syscon f0452000.syscon: regmap [mem 0xf0452000-0xf04520ff] registered
[ 0.050440] No ATAGs?
[ 0.050456] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.050461] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.050626] Broadcom Brahma-B15 readahead cache at: 0xfc3e2478
[ 0.064412] bio: create slab <bio-0> at 0
[ 0.065343] SCSI subsystem initialized
[ 0.065530] libata version 3.00 loaded.
[ 0.065873] usbcore: registered new interface driver usbfs
[ 0.065941] usbcore: registered new interface driver hub
[ 0.066025] usbcore: registered new device driver usb
[ 0.066138] Linux video capture interface: v2.00
[ 0.066336] pps_core: LinuxPPS API ver. 1 registered
[ 0.066340] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 0.066385] PTP clock support registered
[ 0.066943] Advanced Linux Sound Architecture Driver Initialized.
[ 0.067635] cfg80211: Calling CRDA to update world regulatory domain
[ 0.068078] brcm-pci f0460000.pcie: adjusting to legacy (broken) pcie DT
[ 0.068280] brcm-pci f0490000.pcie: adjusting to legacy (broken) pcie DT
[ 0.168654] brcm-pci f0460000.pcie: link down
[ 0.268880] brcm-pci f0490000.pcie: link down
[ 0.268921] Switched to clocksource arch_sys_counter
[ 0.269068] FS-Cache: Loaded
[ 0.276785] NET: Registered protocol family 2
[ 0.277121] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.277137] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.277158] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.277206] TCP: reno registered
[ 0.277213] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.277224] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.277325] NET: Registered protocol family 1
[ 0.277482] RPC: Registered named UNIX socket transport module.
[ 0.277488] RPC: Registered udp transport module.
[ 0.277491] RPC: Registered tcp transport module.
[ 0.277494] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.277500] PCI: CLS 0 bytes, default 64
[ 0.277694] hw perfevents: enabled with ARMv7 Cortex-A15 PMU driver, 7 counters available
[ 0.278712] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.284668] bounce pool size: 64 pages
[ 0.290646] FS-Cache: Netfs 'nfs' registered for caching
[ 0.290953] NFS: Registering the id_resolver key type
[ 0.290975] Key type id_resolver registered
[ 0.290979] Key type id_legacy registered
[ 0.290988] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.290993] Installing knfsd (copyright (C) 1996 [email protected]).
[ 0.291226] FS-Cache: Netfs 'cifs' registered for caching
[ 0.291443] Key type cifs.spnego registered
[ 0.291595] fuse init (API version 7.22)
[ 0.292021] SGI XFS with security attributes, realtime, large block/inode numbers, no debug enabled
[ 0.293246] msgmni has been set to 460
[ 0.293851] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.293858] io scheduler noop registered
[ 0.293874] io scheduler cfq registered (default)
[ 0.294113] brcm-gisb-arb f0400000.gisb-arb: registered mem: fc400000, irqs: 258, 259
[ 0.360325] brcm-cma brcm-cma.0: Initialized Broadcom CMA root device
[ 0.360862] brcm-cma brcm-cma.0: Added CMA device @ PA=0x10000000 LEN=0x1f800000
[ 0.371581] brcm-cma brcm-cma.0: Pre-allocated 0x1f800000 bytes @ 0x10000000
[ 0.372155] brcm-cma brcm-cma.1: Added CMA device @ PA=0x2f800000 LEN=0x10400000
[ 0.377850] brcm-cma brcm-cma.1: Pre-allocated 0x10400000 bytes @ 0x2f800000
[ 0.378438] brcm-cma brcm-cma.2: Added CMA device @ PA=0x80000000 LEN=0x3fc00000
[ 0.398835] brcm-cma brcm-cma.2: Pre-allocated 0x3fc00000 bytes @ 0x80000000
[ 0.399274] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.400792] f040a900.serial: ttyS0 at MMIO 0xf040a900 (irq = 107, base_baud = 5062500) is a 16550A
[ 1.263682] console [ttyS0] enabled
[ 1.267554] f040a940.serial: ttyS1 at MMIO 0xf040a940 (irq = 108, base_baud = 5062500) is a 16550A
[ 1.276868] f040a980.serial: ttyS2 at MMIO 0xf040a980 (irq = 109, base_baud = 5062500) is a 16550A
[ 1.291174] brd: module loaded
[ 1.296709] loop: module loaded
[ 1.300487] ahci brcmstb-ahci.0: can't get clock
[ 1.305201] ahci brcmstb-ahci.0: SSS flag set, parallel bus scan disabled
[ 1.322939] ahci brcmstb-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 1.331566] ahci brcmstb-ahci.0: flags: 64bit ncq sntf stag pm clo pmp slum part
[ 1.341013] scsi0 : ahci_platform
[ 1.344648] scsi1 : ahci_platform
[ 1.348181] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x100 irq 91
[ 1.356113] ata2: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x180 irq 91
[ 1.365252] spi_brcmstb f03e3400.spi: 1-lane output, 3-byte address
[ 1.371647] spi_brcmstb f03e3400.spi: master is unqueued, this is deprecated
[ 1.378971] m25p80 spi32766.0: found gd25q32, expected m25p80
[ 1.384744] m25p80 spi32766.0: gd25q32 (4096 Kbytes)
[ 1.389738] 5 ofpart partitions found on MTD device spi32766.0
[ 1.395580] Creating 5 MTD partitions on "spi32766.0":
[ 1.400728] 0x000000000000-0x000000200000 : "flash0.bolt"
[ 1.406799] 0x000000200000-0x000000210000 : "flash0.macadr"
[ 1.412980] 0x000000210000-0x000000220000 : "flash0.nvram"
[ 1.419038] 0x000000220000-0x000000230000 : "flash0.devtree"
[ 1.425261] 0x000000000000-0x000000400000 : "flash0"
[ 1.431736] libphy: Fixed MDIO Bus: probed
[ 1.436408] bcmgenet f0b00000.ethernet: GENET 4.5 EPHY: 0x1001
[ 1.452927] libphy: bcmgenet MII bus: probed
[ 1.474934] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.481520] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.487369] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.493841] xhci-brcm: xHCI BRCM driver
[ 1.497783] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[ 1.503660] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 1
[ 1.511745] xhci-brcm f0471000.xhci_v2: irq 149, io mem 0xf0471000
[ 1.518430] hub 1-0:1.0: USB hub found
[ 1.522220] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 1.529481] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[ 1.535286] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 2
[ 1.543552] hub 2-0:1.0: USB hub found
[ 1.547322] hub 2-0:1.0: 2 ports detected
[ 1.551693] ehci-brcm: EHCI BRCM driver
[ 1.555625] ehci-brcm f0470300.ehci_v2: EHCI Host Controller
[ 1.561441] ehci-brcm f0470300.ehci_v2: new USB bus registered, assigned bus number 3
[ 1.579394] ehci-brcm f0470300.ehci_v2: irq 145, io mem 0xf0470300
[ 1.590929] ehci-brcm f0470300.ehci_v2: USB 2.0 started, EHCI 1.00
[ 1.597574] hub 3-0:1.0: USB hub found
[ 1.601346] hub 3-0:1.0: 1 port detected
[ 1.605480] ehci-brcm f0470500.ehci_v2: EHCI Host Controller
[ 1.607935] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.616708] ehci-brcm f0470500.ehci_v2: new USB bus registered, assigned bus number 4
[ 1.634661] ehci-brcm f0470500.ehci_v2: irq 146, io mem 0xf0470500
[ 1.645928] ehci-brcm f0470500.ehci_v2: USB 2.0 started, EHCI 1.00
[ 1.652538] hub 4-0:1.0: USB hub found
[ 1.656307] hub 4-0:1.0: 1 port detected
[ 1.660535] ohci-brcm: OHCI BRCM driver
[ 1.664451] ohci-brcm f0470400.ohci_v2: BRCM OHCI controller
[ 1.670260] ohci-brcm f0470400.ohci_v2: new USB bus registered, assigned bus number 5
[ 1.678140] ohci-brcm f0470400.ohci_v2: irq 147, io mem 0xf0470400
[ 1.739387] hub 5-0:1.0: USB hub found
[ 1.743160] hub 5-0:1.0: 1 port detected
[ 1.747274] ohci-brcm f0470600.ohci_v2: BRCM OHCI controller
[ 1.753162] ohci-brcm f0470600.ohci_v2: new USB bus registered, assigned bus number 6
[ 1.761062] ohci-brcm f0470600.ohci_v2: irq 148, io mem 0xf0470600
[ 1.822326] hub 6-0:1.0: USB hub found
[ 1.826099] hub 6-0:1.0: 1 port detected
[ 1.830313] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.836860] ehci-pci: EHCI PCI platform driver
[ 1.841390] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.847608] ohci-pci: OHCI PCI platform driver
[ 1.852286] usbcore: registered new interface driver usb-storage
[ 1.855369] usb 2-2: new SuperSpeed USB device number 2 using xhci-brcm
[ 1.865063] mousedev: PS/2 mouse device common for all mice
[ 1.867092] usb 2-2: Parent hub missing LPM exit latency info. Power management will be impacted.
[ 1.880218] i2c /dev entries driver
[ 1.884077] IR NEC protocol handler initialized
[ 1.888713] IR RC5(x) protocol handler initialized
[ 1.893559] usb-storage 2-2:1.0: USB Mass Storage device detected
[ 1.899680] IR RC6 protocol handler initialized
[ 1.904221] IR JVC protocol handler initialized
[ 1.905042] scsi2 : usb-storage 2-2:1.0
[ 1.912616] IR Sony protocol handler initialized
[ 1.917251] IR RC5 (streamzap) protocol handler initialized
[ 1.922852] IR SANYO protocol handler initialized
[ 1.927572] IR MCE Keyboard/mouse protocol handler initialized
[ 1.933644] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.939470] sdhci: Secure Digital Host Controller Interface driver
[ 1.945663] sdhci: Copyright(c) Pierre Ossman
[ 1.950026] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.956802] mmc0: no vqmmc regulator found
[ 1.960908] mmc0: no vmmc regulator found
[ 1.995928] mmc0: SDHCI controller on f03e0000.sdhci [f03e0000.sdhci] using ADMA
[ 2.005414] mmc1: no vqmmc regulator found
[ 2.009525] mmc1: no vmmc regulator found
[ 2.028941] usb 3-1: new high-speed USB device number 2 using ehci-brcm
[ 2.042931] mmc1: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using ADMA
[ 2.050606] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.059403] usbcore: registered new interface driver usbhid
[ 2.064986] usbhid: USB HID core driver
[ 2.073029] TCP: cubic registered
[ 2.076355] Initializing XFRM netlink socket
[ 2.084525] NET: Registered protocol family 10
[ 2.089689] NET: Registered protocol family 17
[ 2.094162] NET: Registered protocol family 15
[ 2.098859] Key type dns_resolver registered
[ 2.103184] Registering SWP/SWPB emulation handler
[ 2.108371] regulator-dummy: disabling
[ 2.116366] ALSA device list:
[ 2.119349] No soundcards found.
[ 2.121580] mmc1: BKOPS_EN bit is not set
[ 2.127088] Waiting for root device /dev/mmcblk0p4...
[ 2.127815] mmc1: new high speed MMC card at address 0001
[ 2.137806] mmcblk0: mmc1:0001 4FPD3R 3.64 GiB
[ 2.142508] mmcblk0boot0: mmc1:0001 4FPD3R partition 1 4.00 MiB
[ 2.148535] mmcblk0boot1: mmc1:0001 4FPD3R partition 2 4.00 MiB
[ 2.154538] mmcblk0rpmb: mmc1:0001 4FPD3R partition 3 512 KiB
[ 2.164084] mmcblk0: p1 p2 p3 p4
[ 2.170337] mmcblk0boot1: unknown partition table
[ 2.176179] mmcblk0boot0: unknown partition table
[ 2.369438] EXT4-fs (mmcblk0p4): recovery complete
[ 2.374925] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
[ 2.383051] VFS: Mounted root (ext4 filesystem) on device 179:4.
[ 2.389512] devtmpfs: mounted
[ 2.392617] Freeing unused kernel memory: 264K (c0877000 - c08b9000)
[ 2.806182] random: nonblocking pool is initialized
[ 2.928466] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 3.0 PQ: 0 ANSI: 6
[ 2.940196] sd 2:0:0:0: [sda] 60437492 512-byte logical blocks: (30.9 GB/28.8 GiB)
[ 2.950074] sd 2:0:0:0: [sda] Write Protect is off
[ 2.954943] sd 2:0:0:0: [sda] Mode Sense: 4f 00 00 00
[ 2.957907] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 2.960986] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2.975373] sda: sda1
[ 2.982132] sd 2:0:0:0: [sda] Attached SCSI removable disk
[ 3.220091] Platform init...
[ 3.315187] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 4.060252] Platform init... ok.
[ 4.092927] [Front Version = 40]
[ 4.096171] >> No hwtype = 8
[ 4.122575] input: LUNIX3 4K remote control (native) as /devices/virtual/input/input0
[ 4.139789] LUNIX3 4K Linux DVB BCM73xx CI Driver Release Time (27/04/21)
[ 4.828113] BKNI_P_GetTrackAllocEntry_resize: resizing from 5376->8704
[ 4.834670]
[ 4.837330] BKNI_Malloc(linuxkernel) top users:
[ 4.837330] blocks, bytes, filename:line
[ 4.846311]
[ 4.847940] 966, 205800, ../BSEAV/lib/utils/balloc.c:31
[ 4.853879]
[ 5.563607] scanning fe...ftt9760.
[ 5.693825] DVB: registering new adapter (bcmdvb-0)
[ 12.288119] (NULL device *): DVB: registering adapter 0 frontend 0 (BCM7252S DVB-S2)...
[ 12.296200] tunercnt 0 name bcmdvb-0 adapter0
[ 12.308621] DVB: registering new adapter (bcmdvb-1)
[ 12.446516] (NULL device *): DVB: registering adapter 1 frontend 1 (BCM7252S DVB-S2)...
[ 12.454584] tunercnt 1 name bcmdvb-1 adapter1
[ 12.459470] DVB: registering new adapter (bcmdvb-2)
[ 12.566259] (NULL device *): DVB: registering adapter 2 frontend 2 (BCM7252S DVB-S2)...
[ 12.574311] tunercnt 2 name bcmdvb-2 adapter2
[ 12.579004] DVB: registering new adapter (bcmdvb-3)
[ 12.684677] (NULL device *): DVB: registering adapter 3 frontend 3 (BCM7252S DVB-S2)...
[ 12.692710] tunercnt 3 name bcmdvb-3 adapter3
[ 12.697427] DVB: registering new adapter (bcmdvb-4)
[ 12.800196] (NULL device *): DVB: registering adapter 4 frontend 4 (BCM7252S DVB-S2)...
[ 12.808276] tunercnt 4 name bcmdvb-4 adapter4
[ 12.813021] DVB: registering new adapter (bcmdvb-5)
[ 12.920715] (NULL device *): DVB: registering adapter 5 frontend 5 (BCM7252S DVB-S2)...
[ 12.928743] tunercnt 5 name bcmdvb-5 adapter5
[ 12.933424] DVB: registering new adapter (bcmdvb-6)
[ 13.039977] (NULL device *): DVB: registering adapter 6 frontend 6 (BCM7252S DVB-S2)...
[ 13.048096] tunercnt 6 name bcmdvb-6 adapter6
[ 13.052804] DVB: registering new adapter (bcmdvb-7)
[ 13.158876] (NULL device *): DVB: registering adapter 7 frontend 7 (BCM7252S DVB-S2)...
[ 13.166903] tunercnt 7 name bcmdvb-7 adapter7
[ 13.171581] DVB: registering new adapter (bcmdvb-8)
[ 13.182056] (NULL device *): DVB: registering adapter 8 frontend 8 (FTT9760 DVB-C/T/T2)...
[ 13.194427] tunercnt 8 name bcmdvb-8 adapter8
[ 13.204609] DVB: registering new adapter (bcmdvb-9)
[ 13.221872] DVB: registering new adapter (bcmdvb-10)
[ 13.232110] >>>vtuner0: register
[ 13.237498] DVB: registering new adapter (bcmdvb-11)
[ 13.249065] DVB: registering new adapter (bcmdvb-12)
[ 13.259617] DVB: registering new adapter (bcmdvb-13)
[ 13.273461] DVB: registering new adapter (bcmdvb-14)
[ 13.294590] Registering device 'sci', major '238'
[ 13.301261] Version of smartcard driver: [1.0.0]
[ 13.464737] @@^!^@@
[ 13.544072] vmap allocation for size 10301440 failed: use vmalloc=<size> to increase size.
[ 13.552390] vmalloc: allocation failure: 10296543 bytes
[ 13.557712] modprobe: page allocation failure: order:0, mode:0xd0
[ 13.563829] CPU: 0 PID: 1137 Comm: modprobe Tainted: G O 3.14.28 #1
[ 13.571149] [<c0015ff8>] (unwind_backtrace) from [<c0011e9c>] (show_stack+0x10/0x14)
[ 13.578920] [<c0011e9c>] (show_stack) from [<c0651efc>] (dump_stack+0x6c/0x7c)
[ 13.586297] [<c0651efc>] (dump_stack) from [<c00923cc>] (warn_alloc_failed+0xc8/0x10c)
[ 13.594241] [<c00923cc>] (warn_alloc_failed) from [<c00bd074>] (__vmalloc_node_range+0xa8/0xb4)
[ 13.603077] [<c00bd074>] (__vmalloc_node_range) from [<c0012cf8>] (module_alloc+0x40/0x48)
[ 13.611403] [<c0012cf8>] (module_alloc) from [<c0079250>] (module_alloc_update_bounds+0xc/0x5c)
[ 13.620126] [<c0079250>] (module_alloc_update_bounds) from [<c0079ae8>] (load_module+0x838/0x22c4)
[ 13.629224] [<c0079ae8>] (load_module) from [<c007b724>] (SyS_finit_module+0x94/0xcc)
[ 13.637077] [<c007b724>] (SyS_finit_module) from [<c000efa0>] (ret_fast_syscall+0x0/0x30)
[ 13.645375] Mem-info:
[ 13.647658] Normal per-cpu:
[ 13.650496] CPU 0: hi: 90, btch: 15 usd: 46
[ 13.655296] CPU 1: hi: 90, btch: 15 usd: 66
[ 13.660099] HighMem per-cpu:
[ 13.663063] CPU 0: hi: 0, btch: 1 usd: 0
[ 13.667870] CPU 1: hi: 0, btch: 1 usd: 0
[ 13.672707] active_anon:213 inactive_anon:0 isolated_anon:0
[ 13.672707] active_file:3875 inactive_file:1359 isolated_file:0
[ 13.672707] unevictable:0 dirty:18 writeback:0 unstable:0
[ 13.672707] free:228812 slab_reclaimable:569 slab_unreclaimable:1726
[ 13.672707] mapped:385 shmem:1 pagetables:30 bounce:0
[ 13.672707] free_cma:191899
[ 13.704212] Normal free:161740kB min:1940kB low:2424kB high:2908kB active_anon:392kB inactive_anon:0kB active_file:15500kB inactive_file:5432kB unevictable:0kB isolated(
anon):0kB isolated(file):0kB present:262144kB managed:236048kB mlocked:0kB dirty:72kB writeback:0kB mapped:1540kB shmem:4kB slab_reclaimable:2276kB slab_unreclaimable:6904k
B kernel_stack:736kB pagetables:120kB unstable:0kB bounce:0kB free_cma:14088kB writeback_tmp:0kB pages_scanned:0 all_unreclaimable? no
[ 13.746088] lowmem_reserve[]: 0 14272 14272
[ 13.750383] HighMem free:753520kB min:512kB low:4268kB high:8024kB active_anon:424kB inactive_anon:0kB active_file:0kB inactive_file:4kB unevictable:0kB isolated(anon):0
kB isolated(file):0kB present:1835008kB managed:1826816kB mlocked:0kB dirty:0kB writeback:0kB mapped:0kB shmem:0kB slab_reclaimable:0kB slab_unreclaimable:0kB kernel_stack:
0kB pagetables:0kB unstable:0kB bounce:0kB free_cma:753520kB writeback_tmp:0kB pages_scanned:0 all_unreclaimable? no
[ 13.790564] lowmem_reserve[]: 0 0 0
[ 13.794287] Normal: 116*4kB (EM) 35*8kB (UEMC) 13*16kB (EM) 3*32kB (EM) 3*64kB (UM) 2*128kB (EM) 2*256kB (UC) 4*512kB (UEMC) 4*1024kB (UEMC) 1*2048kB (U) 37*4096kB (MRC)
= 161752kB
[ 13.810832] HighMem: 1*4kB (C) 1*8kB (C) 0*16kB 1*32kB (C) 0*64kB 0*128kB 3*256kB (C) 2*512kB (C) 2*1024kB (C) 2*2048kB (C) 182*4096kB (C) = 753452kB
[ 13.824637] 5234 total pagecache pages
[ 13.828400] 0 pages in swap cache
[ 13.831760] Swap cache stats: add 0, delete 0, find 0/0
[ 13.836999] Free swap = 0kB
[ 13.839929] Total swap = 0kB
[ 13.854761] 524288 pages of RAM
[ 13.857929] 228992 free pages
[ 13.861039] 8572 reserved pages
[ 13.864202] 460800 cma reserved pages
[ 13.868032] 1304 slab pages
[ 13.870836] 2321 pages shared
[ 13.873810] 0 pages swap cached
[ 14.010069] EXT4-fs (mmcblk0p4): re-mounted. Opts: data=ordered
[ 14.173663] WARNING: You are using an experimental version of the media stack.
[ 14.173663] As the driver is backported to an older kernel, it doesn't offer
[ 14.173663] enough quality for its usage in production.
[ 14.173663] Use it with care.
[ 14.173663] Latest git patches (needed if you report a bug to [email protected]):
[ 14.173663] 8ed8bba70b4355b1ba029b151ade84475dd12991 media: imx274: remove non-indexed pointers from mode_table
[ 14.173663] 4eb7846d3ead1c2f461811e41e63462016e19ae7 media: imx274: rename and reorder register address definitions
[ 14.173663] f067ddad003b67be8acb7fd739172dcfb4817a2a media: imx274: remove unused data from struct imx274_frmfmt
[ 14.241187] LED trigger rc-feedback failed to register (-17)
[ 14.246876] WARNING: You are using an experimental version of the media stack.
[ 14.246876] As the driver is backported to an older kernel, it doesn't offer
[ 14.246876] enough quality for its usage in production.
[ 14.246876] Use it with care.
[ 14.246876] Latest git patches (needed if you report a bug to [email protected]):
[ 14.246876] 8ed8bba70b4355b1ba029b151ade84475dd12991 media: imx274: remove non-indexed pointers from mode_table
[ 14.246876] 4eb7846d3ead1c2f461811e41e63462016e19ae7 media: imx274: rename and reorder register address definitions
[ 14.246876] f067ddad003b67be8acb7fd739172dcfb4817a2a media: imx274: remove unused data from struct imx274_frmfmt
[ 14.325392] dvb-usb: found a 'Microsoft Xbox One Digital TV Tuner' in cold state, will try to load a firmware
[ 14.352355] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.20.fw'
[ 14.560974] dib0700: firmware started successfully.
[ 15.067121] dvb-usb: found a 'Microsoft Xbox One Digital TV Tuner' in warm state.
[ 15.075170] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[ 15.090496] dvb-usb: Microsoft Xbox One Digital TV Tuner error while loading driver (-23)
[ 15.102205] usbcore: registered new interface driver dvb_usb_dib0700
[ 16.639933] f0b00000.etherne:01: Broadcom BCM7439 (2) PHY revision: 0x10, patch: 1
[ 16.651051] f0b00000.ethernet: configuring instance for internal PHY
[ 16.657468] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.654013] libphy: f0b00000.etherne:01 - Link is Down
[ 20.437671] libphy: f0b00000.etherne:01 - Link is Up - 1000/Full
[ 20.443752] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 39.488636] UDF-fs: warning (device mmcblk0p1): udf_fill_super: No partition found (2)
[ 39.556319] UDF-fs: warning (device mmcblk0p1): udf_fill_super: No partition found (2)
[ 39.585307] UDF-fs: warning (device mmcblk0p3): udf_fill_super: No partition found (2)
[ 39.646319] UDF-fs: warning (device mmcblk0p3): udf_fill_super: No partition found (2)
[ 39.686804] UDF-fs: warning (device mtdblock2): udf_fill_super: No partition found (2)
[ 39.697887] isofs_fill_super: bread failed, dev=mtdblock2, iso_blknum=32, block=64
[ 39.731693] isofs_fill_super: bread failed, dev=mtdblock2, iso_blknum=32, block=64
[ 39.739899] UDF-fs: warning (device mtdblock2): udf_fill_super: No partition found (2)
[ 46.752504] no vt opened...
[ 46.755402] set source 8 bf852ae8 0.
[ 84.862898] - HD_VideoClip out -
[ 86.637402] UDF-fs: warning (device mmcblk0p1): udf_fill_super: No partition found (2)
[ 86.708856] UDF-fs: warning (device mmcblk0p1): udf_fill_super: No partition found (2)
[ 86.737951] UDF-fs: warning (device mmcblk0p3): udf_fill_super: No partition found (2)
[ 86.800534] UDF-fs: warning (device mmcblk0p3): udf_fill_super: No partition found (2)
[ 86.841027] UDF-fs: warning (device mtdblock2): udf_fill_super: No partition found (2)
[ 86.852063] isofs_fill_super: bread failed, dev=mtdblock2, iso_blknum=32, block=64
[ 86.886334] isofs_fill_super: bread failed, dev=mtdblock2, iso_blknum=32, block=64
[ 86.894499] UDF-fs: warning (device mtdblock2): udf_fill_super: No partition found (2)
[ 92.485645] no vt opened...
[ 92.488481] set source 8 bf852ae8 0.

 

[lobosnake]

y esta seguro que el tdt funciona, lo has probado en otro dispositivo para verificar que funciona?? te lo digo porque hace como un par de meses compre uno y tal y como llego tube que devolverlo porque no funcionaba, la suerte que yo tengo otros tdt de xbox y pude verificar que era el tdt el que no funcionaba.

 

[esehomo]

No tengo otro deco para probarlo ni sé como probarlo en el pc, aunque en windows me lo reconoce e instala los drivers. Por los errores entiendo es problema de drivers. Otra cosa es que una vez instalado no vea nada, pero el error parece en la instalación de los drivers.

 

[evox]

No tengo otro deco para probarlo ni sé como probarlo en el pc, aunque en windows me lo reconoce e instala los drivers. Por los errores entiendo es problema de drivers. Otra cosa es que una vez instalado no vea nada, pero el error parece en la instalación de los drivers.

Pues tras diferentes pruebas con y sin tuner interno con un Lunix3 4K tengo malas noticias, No soporta tuners por USB, no es cosa del USBTDT XBOX sino con al menos los 3 diferentes que he testado, con todos pasa lo mismo, con nuestros drivers no carga pero puedes usar la imagen, con los drivers del kernel OE-A la imagen carga el driver pero no arranca la imagen, estas pruebas las he hecho con OpenSPA y también con OpenATV, viendo que este deco es broadcom 7252 me da que pecan del mismo problema de drivers al igual que los Gigablue Quad y UE 4k que tampoco soportan tuners USB.

Seguiremos estudiándolo pero no tengo muchas esperanzas.

Salu2.

 

[Tururu]

De momento lo añado a la lista de decos/receptores que no soportan USB-TDT.
PD:
.

 

[esehomo]

Vaya.... la verdad que los drivers están dándome quebradores de cabeza. Ya tuve problemas con los FBC, que todos los virtuales están conectados al mismo tuner físico, y el otro tuner no tiene ninguno asociado. Tuve que tirar de un openatv bastante antiguo y que me costó encontrar, y que tenía unos drivers anteriores en los que sí funcionaban correctamente. Pero al final terminé instalándome openspa 8 y pasé de los tuner. Tal y como está ahora el tema, tampoco le estaba dando uso.

Muchas gracias a ambos por la ayuda!!!